Archimedes’ principle states that the upward buoyant force experienced by a solid object in a fluid is equal to the weight of the fluid displaced. In mathematical form, Archimedes’ principles states:

Here,is the buoyant force,is the mass of the fluid displaced, andis the acceleration due to gravity. Recall that density is defined as mass divided by volume; therefore, mass of fluid can be written as:

is the density of fluid andis the volume of fluid displaced. Plugging this equation into Archimedes’ principle gives:

Notice that the density of the object is not part of Archimedes’ principle; therefore, the the density of the object doesn’t affect the buoyant force.

Both submerged and floating objects in a fluid will experience an upward buoyant force that is equal to the weight of the fluid displaced; Archimedes’ principle is valid for both submerged and floating objects.

To solve this question, you need to first compare the density of the object with the density of the fluid (water). The density of the object (according to the question) isand the density of water is. Since the density of the object is less than the density of water, the object will float. To solve for the volume of fluid displaced, we need to use Archimedes’ principle:

Here,is buoyant force,is density of fluid,is volume of fluid displaced, andis acceleration due to gravity. We have two unknowns in this equation: the buoyant force and the volume of fluid displaced; therefore, we do not have enough information to solve for the volume of fluid displaced.

If the density of the object and the density of the fluid were equal, then we could have assumed that the weight of the fluid displaced (Buoyant force) equals the weight of the object. We could have then calculated the buoyant force and, subsequently, the volume of fluid displaced; however, we cannot make that assumption in this question because the density of the object is different from the density of the fluid.

的,stion states that the object sinks to the bottom of the bowl. Recall that objects with greater density than water will either submerge completely or sink, whereas objects with lesser density than water will float on the surface of water. The object in this question must have a greater density than water.

The second part of the question is asking you to compare the buoyant force with the weight of the fluid displaced. Archimedes’ principle states that the upward buoyant force always equals the weight of fluid displaced. Archimedes’ principle is valid for floating, submerging, and sinking objects; therefore, the buoyant force on the object will equal the weight of the water displaced.

The density of the object is, whereas the density of water is; therefore, the object will float at the surface of water. One of the implications of Archimedes’ principle for a floating object is that the percent of object submerged equals the ratio of the density of object to the density of fluid:

This means that 50% of the object is submerged and 50% of the object is above the water. 50% of the volume of the object, or, is submerged.

The density of an object is equal to mass over volume.

Knowing the length and the cross sectional area of the log, we can find its volume.

Plugging in volume and mass into the equation will enable us to find density.

The formula for density is:

In the question, we are given the densities of both solids and a means to find their volumes. Using these values, we will be able to determine the mass of each solid.

Now that we know both masses, we can find the difference.

年代olution A and solution X have the same concentration, therefore, we are only concerned with temperature differences between the two solutions. Density is dependent on temperature: as temperature increases density decreases. Recall the definition of density:

Increasing the temperature will slightly increase the volume of the solution and, subsequently, decrease density. The temperature has no effect on mass. The solution at the higher temperature (solution X) will have a lower density.

Plotted in this way, the slope of the line is equal to the density of the substance.

We would expect the line to be linear and positive. A slope close to zero could indicate that the data was not graphed optimally or that the density is extremely small, and a density greater than one is possible (anything that sinks in water has a density greater than one). A negative density would indicate that greater masses of this substance have smaller volumes, which, for a pure substance, does not make sense.

年代olving this question requires that we use the given densities to convert mass to volume.

We see that only the aluminum sample has a volume over three liters.

年代pecific gravity is the density of the substance over the density of water.

Density is given by mass over unit volume.

A boat with a mass of 6000kg and a volume of 10m³will have a density of 600 kg/m³.